R E M O T E M O N I T O R I N G S Y S T E M S
The WESROC Hand Held Monitor is an extremely effective tool for use during installations and trouble shooting. This portable, battery powered diagnostic tool can be used to change the internal Transmitter ID number while outside at the tank. Using a WESROC Hand Held Monitor and two programming magnets, is the only way to change the transmitter scaling in the field. (for 420 lb. propane, 275 gallon heating oil etc.) This field programmable software allows you to stock one transmitter for every type of tank instead of multiple factory-programmed models.
You will save valuable time by diagnosing signal issues with the built in signal strength meter. Just place a programming magnet on the transmitter and slowly walk away with your WESROC Hand Held Monitor. Watch the signal strength indicator as well as the Time Since Last Transmission (TSLT) counter. When the WESROC Hand Held Monitor receives a transmission, the counter resets to zero seconds. Placing the WESROC base unit within range of the WESROC transmitter will eliminate return trips for poor signal. A built in RF noise meter can be used to determine if there are any other signals that might be interfering with the WESROC signal.
The WESROC Hand Held Monitor is a required tool when installing a WESROC Satellite Base Unit. The WESROC Hand Held Monitor is used to wirelessly communicate and program the settings in the Satellite Base Unit.
Heading to the field on an installation or service call without a WESROC Hand Held Monitor is like trying to change a regulator without a pipe wrench, it can be done, but it would be a lot easier with the correct tools.
A WESROC Hand Held Monitor is one of the 5 required items for any installation or trouble ticket. Make sure your technicians have a spare Base Unit, Transmitter, touch tome telephone, WESROC signal repeater, and a Hand Held monitor for every job and you can rest assure with our help they can get the job done.
You will save valuable time by diagnosing signal issues with the built in signal strength meter. Just place a programming magnet on the transmitter and slowly walk away with your WESROC Hand Held Monitor. Watch the signal strength indicator as well as the Time Since Last Transmission (TSLT) counter. When the WESROC Hand Held Monitor receives a transmission, the counter resets to zero seconds. Placing the WESROC base unit within range of the WESROC transmitter will eliminate return trips for poor signal. A built in RF noise meter can be used to determine if there are any other signals that might be interfering with the WESROC signal.
The WESROC Hand Held Monitor is a required tool when installing a WESROC Satellite Base Unit. The WESROC Hand Held Monitor is used to wirelessly communicate and program the settings in the Satellite Base Unit.
Heading to the field on an installation or service call without a WESROC Hand Held Monitor is like trying to change a regulator without a pipe wrench, it can be done, but it would be a lot easier with the correct tools.
A WESROC Hand Held Monitor is one of the 5 required items for any installation or trouble ticket. Make sure your technicians have a spare Base Unit, Transmitter, touch tome telephone, WESROC signal repeater, and a Hand Held monitor for every job and you can rest assure with our help they can get the job done.
To use your WESROC handheld test set to confirm the cell monitor is functioning correctly, you will need to download new software for handheld. To do that, go to: http://www.independenttech.com/handheld/ Enter Login: handheld
Password: handheld0799
Select "RUN" Instructions for the update are displayed when the program begins execution. The first step is to connect the cord that comes with the handheld to the handheld jack on side and the other end to your computer. The cable has an RS-232 connector. If all you have are USB jacks on your computer, you will need an adapter to go from USB to RS-232.
Password: handheld0799
Select "RUN" Instructions for the update are displayed when the program begins execution. The first step is to connect the cord that comes with the handheld to the handheld jack on side and the other end to your computer. The cable has an RS-232 connector. If all you have are USB jacks on your computer, you will need an adapter to go from USB to RS-232.
WESROC Hand Held Monitor (Portable Diagnostic Unit)